Category Archives: My Games

Oct 19 2017
Leave a comment
My Games

WPT shop job initial notes

(Looks like this got written years before it got posted, somewhere around 2015.)

Got a WPT back in late October [2014]. I’ve been playing it, but it’s obviously in need of some love. Decided it was time to start major shop job instead of whatever I should have been doing.

In this case, it starts with the statement: “I’ll just take the upper playfield out in preparation for re-rubbering.” When I get the flippers out, I discover they need a rebuild. All of the rubber is old and hard, and a few lamps are out.

Right ramp has busted welds. Very dirty around pop bumpers. A massive amount of dirt near the upper left flipper, like some rubber has been getting ground up.

Start disassembling and found a couple wire ties in places that were not supposed to have wire ties.

All four flippers are egged out.  You wouldn’t know it on these Stern games, since both of the ramps were still make-able shots, but there must be some flipper power missing.

Two welds are broken on the right ramp.  But I have a friend who can weld enough to fix it.

Upper playfield is very dirty. I could polish it. Or I could install a new part.

I’m switching to the overly bright LED bumper caps on this game. I usually avoid this kind of mod, but in this case, the under upper-playfield area is so very dark, I think it’s called for.

So far I’ve got one ramp out and two wireforms out.

[I got it back together. I installed a new upper playfield. Probably worth it. If these aren’t clean, the “jail” lock doesn’t work right.]

Tagged
Feb 16 2014
Leave a comment
My Games, Tech Tips

a note about rebuilding Gottlieb “fat boy” flippers

In general, I don’t rebuild Gottlieb “fat boy” flippers as part of shopping out a game. This is in contrast to Williams solid-state flippers, which do wear out. The exception is the EOS switch. The lever arm will chew a hole in it over a couple decades of play, and it’s worth checking first. It may be fine, or it may need replacement.  I have also seen the plunger/link crack apart. But otherwise, these flippers just work.

On my Monte Carlo and couldn’t make the Firepower-esque lock shot, up the left side and into a saucer. Without this shot, there’s no multiball, and no way to spin the roulette wheel. The flippers seemed fine otherwise, but were clearly missing some oompf.

I replaced the sleeve because it’s cheap and checked out the link assembly, which seemed to be fine. I decided to get more drastic. I have a couple MA-989 upgrade kits with NOS link assemblies and new EOS switches that should make the EOS switch also nearly indestructible. I decided this was a fine occasion to use one. Ultimately, I replaced the EOS and lane change switches, the coil, the coil stop, the plunger/tip, and the lever that clamps around the flipper shaft. Still, it was weak, and in fact it was a little worse.

But in the process, I had installed the flipper with an angle that was too horizontal at rest. I think I was working off the angle of the left flipper, which wasn’t necessarily right to begin with.  I went back and took a look the flyer and went for a droopier angle, and happily, I can make the shot!

I suspect that flipper mechanism develops a lot of power at the end of its stroke.  Plus, the angle made the flipper play funny, and I may have had a hard time adjusting.

I will keep all the parts I took out as spares—I don’t think they’re bad. And I will pay more attention to the angle in the future.

I am not enamored with the MA-988/MA-989 upgrade kits. They require some care to ensure that the return spring isn’t touching the switch. The geometry of the flipper just doesn’t allow this fix to be very good. Plus, my NOS parts came with NOS factory rust in non-critical locations. The original flippers work pretty well without the fix.anyway. I will probably use these kits up and switch back to the original-issue parts once I exhaust my small supply.

Tagged , , , ,
Feb 07 2014
Leave a comment
My Games, Tech Tips

Flash lamp weirdness

I chased down the flash lamp problems on my Monte Carlo.

The flash lamps next to the roulette wheel were locked on. I found a out-of-spec transistor on the driver board.  The under-playfield transistor (MJ2955) tested fine once the driver board was disconnected, so I just left it.

The other one was weirder. The “left dome” flashers did not work. Lamps themselves were fine. The transistors tested okay, and there was voltage at the lamp socket, but grounding the lamp socket did not cause the lamps to light.

I found that the two lugs of the lamp socket were shorted together. Apparently the resistor in circuit that steps down the voltage is good enough to protect the transistors from failing, or I just got lucky.

I might have caught this sooner if I’d noticed that the last person to re-rubber the game had looped rubber around 89 sockets rather than reading the manual for the correct rubber ring sizes.

Tagged , , ,
Feb 02 2014
Leave a comment
My Games

My Monte Carlo

In March 2013, I picked up a Monte Carlo. Nominally, it was working. But it needs some work. Here’s a rundown so far.

The head glass was cracked in two pieces, held together by the trim — just barely. I got a new one through a friend who got it cheap, but we got it cut just a little too small.

Next, the mezzanine board on the MPU was cracked.  All System 80B games self destruct because of this damn board.  Because it is single-sided, and all single-sided boards on a pinball get cracked header pins, it causes the computer to become unreliable, if it boots at all.  Someone had “fixed” mine by jamming packing peanuts in it.  I fixed it by desoldering it, removing solder, adding fresh solder, and putting it back.

Fortunately, this game shipped with one of the cordless phone-style batteries and had not leaked.  Unfortunately I got a little ahead of myself when removing it and I lifted a trace.  I replaced it with a memory cap and did an OK job, but the lifted trace still annoys me.  It was otherwise a perfect MPU.

The right flipper was weak, so I couldn’t get multiball started, because I couldn’t make the Firepower top-capture shot.  But worst of all, the roulette wheel had dirty switches, which meant that there was no way to win roulette and the game would have to time-out every roulette spin.  Terrible!

I did immediately start looking for a topper, and found one locally. I cleaned and reinstalled it and it looks great, or at least as good as that topper ever looked.

Around this time, I bought my Spring Break and got sidetracked, since I’d never even played Spring Break.

After almost a year, I’m back trying to play Monte Carlo. First order of business was the roulette wheel.

The spinning bit is held on with a set screw that might be accessible without removing the assembly. Removing the whole assembly is a good idea to clean it. But if you remove the six screws holding the window on, then take the set screw out, you can probably lift the wheel out.

The wheel has twelve switches and I guarantee they’re all dirty.  I cleaned them with whatever scrap of paper was in my pocket and now it works pretty well.

I also put new foam washers to hold the window on. Now, the window is much closer to level with the playfield.

Now, I went to play it, and the game wouldn’t kick out the third ball to start multiball. I noticed while in test mode (testing the wheel) that switch 42 was stuck closed. The manual says that’s the trough. How can the trough have only one switch? I have no idea, but that’s all it has. On that one switch, the backing blade was bent against the playfield-touching blade.  I adjusted it, and now I have multiball.

Still to go:

  • Right flipper too weak.  Left flipper too, perhaps, but we’ll see.
  • A couple light sockets are bad. Target #5 is burned out, and the bulb is the most inaccessible light I’ve ever seen on a playfield.
  • +5V filter cap hack on transformer panel should be cleaned up
  • add redundant +5V/ground lines on MPU-driver cable
  • blown transistor for the flash lamp on the roulette wheel; lamps are missing from their sockets because they’re locked on (and burned the playfield!)
Tagged , ,
Jan 25 2014
Leave a comment
Collecting, My Games

I bought a (Bally) Star Trek; or, how not to drill a lock

A friend posted a link to a $400 Bally Star Trek on Craigslist. It was clearly bombed out, but I was looking for a restoration candidate. I went for it.

The seller said he didn’t have the head key. This meant two things: first, it was going to take a  big vehicle to move it back to my house. Second, the computer was going to be corroded. But the game was mostly working, how bad could it be?

I a U-Haul van, a little Ford Econoline, at the place near my house, and headed to the seller’s place. I got there around 5 and after some smalltalk, I paid and then started figuring out how to get the game in the van. I have skates so it wasn’t too bad. I got the front legs off and we got the front of the game onto the van; then, the back legs off, and slid the game right into the door latch of the van.

That’s right, a classic solid state Bally game won’t fit in an Econoline van with the head on.

Fortunately, I was somewhat prepared for this eventuality and had my drill and a bunch of bits. But I didn’t think carefully about how the backbox works and spent two hours trying to open a door instead of just lifting the glass out.

I finally lifted the glass out in the relative dark and got the game home in three pieces: head, cabinet, and glass, which I won’t put back in until I have a proper lift channel on it.

Anyway, I bought the game in early November and am just starting to shop it. Eventually I’d like to restore it, but this is at the end of a long list of projects.

Tagged ,
Jan 12 2014
Leave a comment
My Games, Tech Tips

Williams EMs Sometimes Have Interlock Switches

I decided to spend a few minutes trying to fix my Spanish Eyes.  It just wasn’t getting power at all.

I stared at the schematic for a while and chatted with Chris a bit, and he said, “Is there an interlock switch?”

Yep, sure enough, there is.

Gottlieb and Williams games, particularly those with three-prong power cords, have interlock switches and the coin door must be closed for operation. It is even rarer to find one that has not been bypassed.

And it’s not in my schematic!  I don’t know why.  I might guess that it was a factory option, on some games, but I know of other Spanish Eyes that don’t have the interlock switch. It looks factory, and I can’t imagine anyone ADDING an interlock switch.

(An interlock switch cuts power when the coin door.  Most video games have them on the back panel, and some games, particularly early ’80s Atari games, have them on the coin door.)

Tagged
Jul 18 2013
Leave a comment
My Games, Tech Tips

Spring Break restoration notes

Old notes are bulleted, with inner bullets updating the work I did:

  • Battery corrosion.  This had one of the “DataSentry” style black batteries of doom.  … I have so far removed the battery but not cleaned the damage.
    • Ultimately, I just stopped.  I have parts to rebuild the reset section, but it’s working; why fight with it?
  • Computer has been trashed.  Like every 80B computer, this has a piggyback board arrangement where the solder joints fatigue and crack. … [T]his involves desoldering the board so I can work on the underside.  Unfortunately someone decided to go to war with the thing on the top side.  I did finally get the board off, but I am afraid I have damaged the plated-through holes.  I obliterated at least one pad on the bottom and damaged another.
    • I bought one of the GPE daughterboards.  Highly recommended.  The redundancy that this board adds helps make up for my mistakes, and Gottlieb’s mistakes.
  • Ramp cracked at entrance badly.
    • I have a new ramp, but it’s not installed.
  • Sounds lacking.  So I can hear some correct sounds, but mostly it’s static.  Can’t hear the music. I want to take a look at this, but there’s no reason to until grounds are verified.
    • I did put this off until after the ground mods, but the ground mods weren’t required.  All the grounds in this game are one big common (eventually) and that was easy to verify.
    • The actual problem was one or more bad ROMs on the sound board. I verified this by swapping parts with my Monte Carlo, which had a working sound board. This was much easier than trying to go at it with an oscilloscope… which I also did.
  • Ground mods not done.  I suspect this is causing sound problems.  At least one set of pins (this game has five) is burned badly.
    • I did the major ground mods.  Didn’t fix the sound (not surprising).  I’m not happy with them, though, because it means permanently rerouting a cable in a way I just don’t love.  I may try and come up with another method the next time I do this.
  • Lots of lamps missing.
    • Bad sockets and bad bulbs. I need to solder some sockets “shut”, but that’s about it.
  • Driver board has transistors replaced with the twisted-leg hack.
    • Replaced with CEN-U45.
  • Black rubber on playfield.  Ew.
    • Yeah, still haven’t had time to shop the game.
Tagged , , ,
May 13 2013
Leave a comment
My Games

I bought a Spring Break

Chris goes to the Captain’s Auction Warehouse coin-op auction regularly, at least recently. I started getting some bids in on some weirder titles that are going for reasonable prices. First I got a Spanish Eyes, then a Monte Carlo.  Most recently I picked up a Spring Break for $500, plus premiums and tax, which are actually pretty steep.

But I was happy to get it. The game is complete. The playfield is a little rough, but they’re still available. The cabinet is very good.

So far, I’ve found the following problems with it:

  • +5v regulator pot was bad.  They’re all bad, unless they have been replaced.  Mine was running a little north of +5v and the adjustment pot just didn’t work.  I replaced it, and it’s OK.
  • Battery corrosion.  This had one of the “DataSentry” style black batteries of doom.  Unlike my Monte Carlo, which is a few months older and had a beautiful, clean computer, this one has some damage in the reset section.  I have so far removed the battery but not cleaned the damage.
  • Computer has been trashed.  Like every 80B computer, this has a piggyback board arrangement where the solder joints fatigue and crack.  The solution is straightforward: resolder the pins.  The difficulty is that this involves desoldering the board so I can work on the underside.  Unfortunately someone decided to go to war with the thing on the top side.  I did finally get the board off, but I am afraid I have damaged the plated-through holes.  I obliterated at least one pad on the bottom and damaged another.  This won’t be too hard to mitigate, but it probably would not have happened had someone done good work to begin with.
  • Ramp cracked at entrance badly.
  • Sounds lacking.  So I can hear some correct sounds, but mostly it’s static.  Can’t hear the music. I want to take a look at this, but there’s no reason to until grounds are verified.
  • Ground mods not done.  I suspect this is causing sound problems.  At least one set of pins (this game has five) is burned badly.
  • Lots of lamps missing.
  • Driver board has transistors replaced with the twisted-leg hack.  I have the right transistors and I’ll fix that.
  • Black rubber on playfield.  Ew.

On the upside, a lot of lamps DO work.  The flippers are pretty strong.  The cabinet is very good, other than some duck tape glue that should be pretty easy to clean off.  The translite is a little faded, but not too bad.  I dropped in the regulator and computer from my Monte Carlo, and that gave a lot of hope.

Tagged , , ,
Newer posts →