Tag Archives: stern trek

Installing a knocker in Stern’s Star Trek

I have had a Star Trek (Pro) and the parts for a knocker install, for well over two years. I decided it was time. I think this general plan would go for any metal-head game.

Get a real manual from an old SAM game. This is helpful in finding places to pick up the needed voltages. I used WPT, because I have one. Stern manuals are terrible after about 2008, but they were superb before that.

To tap voltages off existing connectors, get an IDC punch-down tool for .156″ pins. The trick to these is to run the wire into the connector just far enough. If it’s too far, it won’t punch down on the far side, no matter how hard you push.

Star Trek never had a high voltage board for its DMD, so there are some mounting posts in the head not being used. Maybe it’s different in the LE. I installed the same step-up board that I used in WPT and Simpsons, except it now requires +20V. I just put it on one post and held it down with a #8 nut.

The real pain point in installing the knocker is figuring out where to pick up the needed voltages. The 520-5254-00 step up board requires +50V, +20V, solenoid ground, solenoid input (from Q24) and solenoid output. (Older versions of this board omit the +20V but sometimes pull in at power on. Like a System 80 game!)

The cable dressing here is pretty terrible. I may have to re-do this due to poor crimping anyway, and if I do, I will trim all of the wires to the same length and dress the harness neatly.


+20V is available on J7-1, right next to another source that the game actually uses. In my Star Trek, it’s a fat orange wire. I suspect most SAM games have available +20V pins.


Solenoid ground is available from J10-2,4,5. On Star Trek, pins 2 and 4 are not populated, so I stuffed a wire into pin 2. It appears the game generally uses black for this. I suspect most SAM games have available grounds.

+50V is not as easy to get on Star Trek, as there are no spare supplies. On WPT, the dedicated magnet supply wasn’t used, so there was an unused pin in the J10 connector. Star Trek, however, has a magnet. I tapped the magnet with a suitcase connector (Scotchlok). I had some trouble getting this to make contact. I either didn’t squeeze hard enough, or the second wire slipped out of position before I clamped down. In either case, next time, I’ll check continuity immediately before moving onto the next step.

I also crimped two wires into the +50V pin for the step-up board so that I’d have a +50V wire to feed the coil with. I probably won’t do that again. Another suitcase connector would have worked just as well. (In my WPT, I fed +50V to the coil, then daisy chained it to the step-up board, which is a better idea when putting the knocker in the head.)

I ran a long cable with three wires out of the head and into the cabinet. One wire picks up the Q24 output and gives it to the step-up board. One is +50V and one is the output from the step-up board to fire the solenoid.

Knocker mounting in cabinet

Knocker mounting in cabinet

I screwed the knocker in the bottom and firing at the cross member near the coin box. I used screws that are a little too long and pierced the bottom of the cabinet. The cabinet bottom is not great plywood. I may change this over to T-nuts in the future. I believe I based this particular mounting on APB Enterprises’ directions on how to mount a knocker for their kits. For my WPT mount, I eyeballed it and it’s relatively close to the coil–and wonderfully loud.

If I make any further changes, or I do this again, I want more connectors to make the harness a little easier to work with and debug. Having the connector near the solenoid makes cable management easier. Having connectors for the patches into the existing connectors would make removal easier.

Another possible improvement: Does the shaker motor offer a place to hook in for +50V?

Tagged ,